Straightforward Guide to Installing a New Shower Unit
Straightforward Guide to Installing a New Shower Unit
Blog Article
We've uncovered this great article on How to Install a Direct-to-Stud Shower Enclosure down the page on the internet and think it made perfect sense to write about it with you on this page.

A successful shower setup needs cautious planning as well as a great deal of work. For the most part, you will certainly need to do three kinds of jobs: framing walls, setting up the plumbing, and also ending up walls.
Various Kinds Of Shower Units
A Lot Of Usual Mistakes
Preparation.
First of all, you should decide on the sort of shower that you want to mount. It is very important to establish whether the picked shower is capable of handling particular systems and can control a safe level of water via the central heating boiler. A lot of shower systems nowadays are made to be adaptable to various water stress (such as kept hot water and cool mains).
It is also crucial to take into consideration the water stress and the preparation of the piping and also drainage for the shower.
Method.
Relying on the kind of shower you wish to install, the shower head have to either be fitted in order to prevent its contact with the water in the bathroom listed below or the base tray, or it must have a check shutoff.
Before beginning, it is recommended to note the settings of the shower head and control, and to plan the pipe-work entailed. In addition, the drain system to remove the drainage will require to be intended. Both placements of the cable route as well as the shower switch will likewise need to be thought about if an immediate or electrical shower system is being set up.
Make use of the direction guide provided with the shower unit to fit the shower control.Before fitting the pipelines that will supply the water to the shower system, it is very important to remove the water. In order to protect the pipes, they should be offered a water resistant covering and likewise fitted with separating shutoffs. The pipelines can then be buried into the wall and smudged over to neaten the overall appearance.
Fit the base tray, shower head, as well as installations.
Attach the major shower control to the pipelines that will certainly be providing the water (This may call for a female screw thread adapter).
Reconnect the water and also examination the pipes for any type of leakages, as some may need tightening.
If you are installing an electrical shower, bear in mind to turn off the power supply prior to making any kind of electrical connections. Once these connections have been made (there ought to be guidance within the user's manual), the power supply can be switched over back on.
Readjusting Water Pressure to Match Your Shower.
The cold water reservoir can be lifted to a greater height (occasionally as little as 150mm (6inches)) by installation a solid wood assistance below it - possibly composed of struts and blockboards. If you select this option, the main and circulation pipes will certainly additionally need to be elevated to meet the new height of the reservoir.
Alternatively, a booster pump (a solitary pump or a dual/twin pump) can be fitted. Whichever kind is chosen, it should be attached into the power supply in order to operate.
Piping as well as Drainage.
It is best to utilize 15mm size supply pipes, and also make the go to the shower as short and straight as feasible so as to maintain maximum stress as well as minimise warm loss. In addition, by reducing using joints for pipe corners, you can lower the resistance in the flow of the supply of water. You can accomplish this by bending the pipelines rather.
How Do You Install a Shower? Follow This Guide
Installing a Shower at a Glance
Tools & Materials: Level, electric drill, caulk, hole saw, cedar shims, shower unit Step 1: Drill pilot holes Step 2: Prep fixture holes Step 3: Move unit into place Step 4: Caulk corners and base Step 5: Attach door Step 6: Install shower pan Whenever plumbing is involved in a DIY project, people worry about what might go wrong. The truth is that installing a shower isn’t that complicated, and you can save a lot of money by doing it yourself. You shouldn’t need to make any alterations to your plumbing to complete the job, and most of the tools you need will be provided in your new shower kit.
Can I Install a Shower Myself?
Even if you’ve never installed a shower before, you’ll find this to be a project that is perfectly suited for DIYers with a moderate level of experience. Whether you're doing a bathtub conversion or installing a new stall, most of what you need comes in shower kits that you can purchase from a hardware store. The first thing you need to do is determine what type of shower stall you want.
Single-panel stalls are the easiest to install because they come preassembled. All you need to do is put them in place. Multi-panel showers require a few additional steps, but you’ve got more control over the appearance of your unit. Multi-panel units are also much easier to handle if you’re going to do the installation without any help.
Be sure to take all appropriate safety precautions, such as wearing eye protection and gloves. When you’re removing or installing a shower unit, you might kick up debris that could hurt your eyes. You’ll also need to work with equipment that will get extremely hot, so be sure to have safety gloves handy.
Tools and Materials
2- to 4-foot level Electric drill with a 1/8-inch drill bit Caulk 2-inch hole saw Cedar shims The unit itself Before You Begin: Prep the Space
It’s highly important to measure your space accurately before putting the stall in. Measuring from the floor upward and from each corner outward will ensure you’ve got the right measurements. What you’re looking for is where the plumbing apparatuses are going to come through the stall. Transfer these measurements over to the back of your unit by drawing the locations of these holes using a pencil or marker.
Pull out your old shower and make sure to scrape off all the old caulking. Be thorough because you want to work with smooth surfaces for the best installation. Once you’ve pulled out your existing shower, you need to make sure that the floor is clean and dry. The best way to clean debris is with a shop vacuum, as it’ll soak up water and dirt together.
If you’re experiencing any plumbing issues, such as low water pressure, this is a perfect opportunity to solve them. Make sure that the pipes themselves are not in need of patching and clean your showerhead. When you turn the water back on after your project, check the pipes for signs of wear or disrepair. Anything beyond minor repairs should be handled by a plumber, and this is the best time to bring in a professional.
If the floor has any moisture at all, don’t proceed until it’s completely dry. The last thing you need is for the floor to rot or invite mold and mildew into your base. Once everything is dry, apply waterproof wallboard to the walls. This can be attached with screws or nails, then sealed with caulk so that water doesn’t seep into any crevices.

We were guided to that editorial on How to Install a Freestand through a friend on our other blog. Kindly take the opportunity to share this article if you liked it. I enjoy reading our article about Simple ways to Install a Shower Cubicle on Your Own.
Call Report this page